PV-3310G - Tripod Magnus - Free user manual and instructions

Product Type	Tripod
Brand	Magnus
Model	PV-3310G
Maximum Height	170 cm
Minimum Height	70 cm
Folded Length	85 cm
Weight	3.2 kg
Load Capacity	8 kg
Leg Sections	3
Leg Material	Aluminum
Head Type	Fluid head
Quick Release Plate	Included (standard Arca-Swiss compatible)
Leveling Bubble	Yes
Spiked or Rubber Feet	Rubber feet with retractable spikes
Center Column	Geared or quick-release (depending on version)
Maintenance	Clean with dry cloth; avoid water; tighten screws periodically
Safety	Secure camera with strap; avoid overloading; use on stable surface
Repairability	Spare parts available from Magnus; user-replaceable feet and plates
Warranty	1 year limited warranty
Intended Use	Video and photography support

Frequently Asked Questions - PV-3310G Magnus

How do I extend the legs of the Magnus PV-3310G tripod?

To extend the legs, loosen the leg locks by turning them counterclockwise. Pull the leg sections out to the desired length, then tighten the locks by turning clockwise. Ensure all locks are tight for stability.

How to mount a camera on the tripod?

Attach the quick release plate to your camera using the 1/4-20 screw. Then slide the plate into the tripod head until it clicks. Ensure the plate is locked securely by checking the safety pin.

What is the maximum load capacity of the PV-3310G?

The maximum load capacity is 8 kg (17.6 lbs). Do not exceed this weight to avoid damage or instability.

How to adjust the fluid head tension?

Locate the tension knob on the side of the head. Turn clockwise to increase tension (slower movement) or counterclockwise to decrease (faster movement). Adjust to your preference for smooth panning.

Can I use the tripod for low-angle shots?

Yes, you can spread the legs as wide as possible and lower the center column, or remove it entirely for ground-level shots. Some models allow the center column to be reversed for even lower angles.

How to clean and maintain the tripod?

Wipe the legs and head with a dry or slightly damp cloth. Avoid using harsh chemicals. After use in sandy or salty environments, rinse with fresh water and dry thoroughly. Periodically lubricate the leg locks with silicone grease if they become stiff.

What should I do if the quick release plate is not locking?

Check if the plate is correctly aligned and pushed in fully. Ensure the locking lever is in the correct position. If it still fails, inspect the plate for damage or debris. Clean the plate and head groove. If problems persist, contact Magnus support for replacement.

Are spare parts available for the PV-3310G?

Yes, Magnus offers spare parts such as replacement feet, quick release plates, and leg locks. Contact their customer service or visit the official website for ordering.

How to convert between rubber feet and spikes?

The feet are retractable: pull down the rubber part to expose the spike, or push up to cover it. This allows use on slippery or soft terrain.

Does the tripod come with a carrying case?

Yes, the Magnus PV-3310G typically includes a padded carrying case with a shoulder strap for convenient transport and storage.

USER MANUAL PV-3310G Magnus

MAGNUS®

Photo/Video Tripod

Thank you for choosing Magnus.

Congratulations on the purchase of your new Magnus tripod. This tripod features a geared center column for smooth and precise camera height adjustment. The telescoping legs with flip-locks allow for fast and easy setup, breakdown, and leg length adjustments. A three-way pan-and-tilt head employs a quick-release mounting plate with a universal 1/4-20 mounting screw that is compatible with most cameras' mounting sockets.

Please read and follow these instructions, and keep this manual in a safe place.

Photo/Video Tripod Components

Opening the Tripod

1
Always extend the legs from the top flip-locks first. Pull out on each flip-lock, and extend the legs to the desired height. Relock each leg. (Fig. A-B)

Close-up of a hand adjusting a black mechanical component with a green arrow indicating the tip (no text or symbols visible)

Figure A

Close-up of hands holding a black mechanical component with a yellow arrow indicating direction (no text or symbols visible)

Figure B
2

Rotate the locking collar counterclockwise to release the center brace, and gently pull the legs out. Push down on the center brace, and then rotate the locking collar clockwise to lock the legs in place. (Fig. C)

Hand adjusting a black tripod stand with a hook, no visible text or symbols

Figure C

Mounting the Quick-Release Plate to the Camera

1

To remove the quick-release plate from the tripod head, pull and hold the plate locking lever, and remove the quick-release plate. (Fig. D)

Close-up of hands adjusting a black mechanical device with a clip (no visible text or symbols)

Figure D
2

Line up the quick-release plate lengthwise with the bottom of the camera. Match the quick-release plate screw to the camera's mounting thread, and mount the plate to the camera by rotating the screw clockwise until snug. (Fig. E)

Close-up of hands holding a black camera module with lens and adjustment knobs (no visible text or symbols)

Figure E

Make sure the screwhead handle is flat against the bottom of the quick-release plate. Mount the camera/quick-release plate assembly to the tripod head by pulling and holding back on the plate locking lever. Insert the assembly, and let go of the lever to lock it in place. (Fig. F)

Close-up of hands using a DSLR camera to adjust the camera's clip (no text or symbols visible)

Figure F

Using the Pan & Tilt Head

To use the tilt feature, loosen the tilt/pan bar by rotating it counterclockwise. Tilt the tripod head to the desired angle, and then rotate the pan & tilt bar clockwise to lock the new position. (Fig. G)

Hand holding a camera stick applying green motion to a tripod-mounted device (no text or symbols visible)

Figure G

To use the 360° panning feature, loosen the pan locking knob by rotating it counterclockwise. Pan as necessary, and then rotate the pan locking knob clockwise to lock the new position. (Fig. H)

Close-up of a hand adjusting a camera tripod-mounted device with a yellow arrow pointing to the adjustment knob (no text or symbols visible)

Figure H

To change the camera orientation from horizontal to vertical position, loosen the platform orientation

locking knob by rotating it counterclockwise. Rotate the platform 90°, and then rotate the platform locking knob clockwise to lock the new position. (Fig. I)

Close-up of a hand adjusting a camera module with a green accent (no text or symbols visible)

Figure 1

Adjusting the Center Column Height

To raise or lower the center column, loosen the center column locking knob by rotating it counterclockwise. (Fig. J)

Close-up of a hand adjusting a black mechanical component with a green arrow indicating rotation (no text or symbols visible)

Figure J

2 Wind the crank clockwise to raise the center column to the desired height, or counterclockwise to lower it (Fig. K). Rotate the center column locking knob clockwise to lock the new position.

Make sure to keep one hand on the camera while adjusting the height.

Close-up of a hand adjusting a camera tripod-mounted device with green directional arrows indicating motion (no text or symbols visible)

Figure K

All images are for illustration purposes only. Features vary by model.

User Cautions

• Never set up or pull down a tripod while a camera is mounted.
• Do not move the tripod or adjust the legs while a camera is mounted
• Do not exceed the maximum weight capacity of the tripod
  • Never leave a camera unattended on the tripod
• The camera should be securely fastened to the quick-release mounting plate before mounting onto the tripod
• Never mount a camera to the tripod until all tripod legs are locked and stabilized
• Do not stand on, rest on, or hang anything from the mid-level spreader
• Do not attempt to remove the mid-level spreader
  • Do not lift or move the tripod by the head
• Keep hands clear of the inside of the legs to avoid trapping fingers
• The safe operation of the tripod is the responsibility of the user

ONE-YEAR LIMITED WARRANTY

This Magnus product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later. The warranty provider's responsibility with respect to this limited warranty shall be limited solely to repair or replacement, at the provider's discretion, of any product that fails during normal use of this product in its intended manner and in its intended environment. Inoperability of the product or part(s) shall be determined by the warranty provider. If the product has been discontinued, the warranty provider reserves the right to replace it with a model of equivalent quality and function. This warranty does not cover damage or defect caused by misuse, neglect, accident, alteration, abuse, improper installation or maintenance. EXCEPT AS PROVIDED HEREIN, THE WARRANTY PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. This warranty provides you with specific legal rights, and you may also have additional rights that vary from state to state. To obtain warranty coverage, contact the Magnus Customer Service Department to obtain a return merchandise authorization ("RMA") number, and return the defective product to Magnus along with the RMA number and proof of purchase. Shipment of the defective product is at the purchaser's own risk and expense.

For more information or to arrange service, visit www.magnustripods.com or call Customer Service at 212-594-2353.