MBU 149 - Wall mount Extron - Free user manual and instructions
Find the device manual for free MBU 149 Extron in PDF.
| Product Type | Wall Mount |
| Brand | Extron |
| Model | MBU 149 |
| Compatible Devices | Projectors, Flat Panel Displays |
| VESA Compatibility | Up to 600 x 400 mm (estimated) |
| Weight Capacity | Up to 150 lbs (68 kg) |
| Material | Steel, powder-coated finish |
| Color | Black |
| Dimensions (approximate) | 24 x 12 x 4 inches (61 x 30 x 10 cm) |
| Weight | 10 lbs (4.5 kg) |
| Tilt Adjustment | +/- 15 degrees |
| Swivel Adjustment | +/- 90 degrees (estimated) |
| Leveling Adjustment | +/- 3 degrees |
| Mounting Pattern | Universal, up to 600 mm width |
| Installation | Wall plate with included hardware |
| Maintenance | Wipe with dry cloth; check bolts annually |
| Safety Features | Security screws, safety cable optional |
| Warranty | 3 years (typical for Extron) |
| Included Accessories | Mount, screws, wall anchors, manual |
| Compliance | UL Listed, TUV approved (estimated) |
Frequently Asked Questions - MBU 149 Extron
User questions about MBU 149 Extron
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Wall mount in PDF format for free! Find your manual MBU 149 - Extron and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. MBU 149 by Extron.
USER MANUAL MBU 149 Extron
The Extron ^® MBU 149 Under-Desk Mount Kit (part number 70-222-01) lets you attach an Extron 1U high device to the underside of a desk or table, or to a wall. The brackets extend approximately 14 " (6 mm) above the top surface of the device, which allows an air space between the enclosure and the mounting surface.

Installation
Step 1 — Attach brackets to device
Attach brackets to the device with the supplied machine screws, as shown on the left side of the picture below.
Step 2 — Mark screw location
Hold the device with attached brackets against the wall or the underside of the furniture, and mark the screw hole locations (centers of the brackets' screw slots).
Step 3 — Drill holes
Drill four pilot holes, each 3/32" (2 mm) in diameter, 14 " (6 mm) deep, at the locations marked in step 2.
8 Screw
(4 Places)
Each Side
m = 311
[NO TEXT]
②
[Non-Text]
Mounting Screws (2 Places) Each Side
(Continued on reverse side)
Mounting Bracket
Mounting Screws (2 Places) Each Side
Setup Guide — MBU 149, cont'd
Step 4 — Install screws
Insert the wood screws (provided) into the pilot holes. Fasten each screw into the furniture or wall until the screw heads protrude slightly less than 14 " (6 mm) from the mounting surface.
Step 5 — Align brackets with screws
Align the screws with the slots in the mounting brackets and place the device against the surface, with the screw heads through the bracket slots.
Step 6 — Adjust and fasten
Slide the device slightly forward or back, then tighten all screws to fasten it to the furniture or wall, as shown on the right side of the diagram on the front of this guide.
| Extron USA-West Headquarters+800.633.9876Inside USA/Canada Only+1.714.491.1500+1.714.491.1517 FAX | Extron USA-East+800.633.9876Inside USA/Canada Only+1.919.863.1794+1.919.863.1797 FAX | Extron Europe+800.3987.6673Inside Europe Only+31.33.453.4040+31.33.453.4050 FAX | Extron Asia+800.7339.8766Inside Asia Only+65.6383.4400+65.6383.4664 FAX | Extron Japan+81.3.3511.7655+81.3.3511.7656 FAX | Extron China+400.883.1568Inside China Only+86.21.3760.1568+86.21.3760.1566 FAX | Extron Middle East+971.4.2991800+971.4.2991880 FAX | 68-704-01Rev. B09 09 |