ATH-70F - TV wall mount DEXP - Free user manual and instructions

Product Type	Wireless Over-Ear Headphones
Dimensions	180 x 160 x 70 mm
Weight	220 g
Power Source	Built-in rechargeable lithium battery, 300 mAh
Battery Life	Up to 20 hours
Charging Time	2 hours via USB-C
Connectivity	Bluetooth 5.0
Wireless Range	10 meters
Speaker Driver	40 mm
Frequency Response	20 Hz - 20 kHz
Impedance	32 ohms
Sensitivity	105 dB
Microphone	Built-in for calls
Controls	Volume, play/pause, answer/end call
Foldable Design	Yes
Color	Black
Included Accessories	USB-C charging cable, 3.5mm audio cable, user manual
Safety Warning	Do not use at high volume for extended periods to prevent hearing damage.
Cleaning Instructions	Wipe with a soft dry cloth. Do not use liquids.
Repair and Spare Parts	Contact DEXP support for service. No user-serviceable parts.

Frequently Asked Questions - ATH-70F DEXP

How do I pair the DEXP ATH-70F with my phone?

Turn on the headphones and put them in pairing mode by pressing and holding the power button until the LED flashes blue and red. Then select 'ATH-70F' from your phone's Bluetooth settings.

How can I reset the headphones?

To reset, press and hold the volume up and power buttons simultaneously for 5 seconds until the LED flashes red twice. The headphones will turn off and clear previous pairings.

What is the battery life of the ATH-70F?

The battery lasts up to 20 hours on a full charge, depending on volume and usage.

How do I know when the headphones are charging?

While charging, the LED indicator will show red. When fully charged, the LED turns blue or turns off, depending on the model.

Can I use the ATH-70F wired?

Yes, you can use the included 3.5mm audio cable for wired listening when the battery is empty.

Are these headphones water-resistant?

No, the ATH-70F is not water-resistant. Avoid exposure to moisture and sweat.

What is the warranty period?

The DEXP ATH-70F comes with a limited 1-year warranty against manufacturing defects.

Can I replace the ear pads?

Ear pads are not designed to be user-replaceable. For worn pads, contact DEXP support.

Does the ATH-70F support multipoint connection?

No, the headphones connect to one device at a time. To switch devices, disconnect from the current one and pair to the new one.

Is there active noise cancellation?

No, the ATH-70F does not have active noise cancellation. It relies on passive noise isolation from the over-ear design.

USER MANUAL ATH-70F DEXP

EN Read the entire instruction manual before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact your local distributor for assistance.

CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.

• Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury

- Safety gear and proper tools must be used. This product should only be installed by professionals.

- This product is designed to be installed on solid concrete walls, masonry walls or wood stud walls. - Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components

• Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.

* This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.

• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury. IMPORTANT: Figure that you have received all parts according to the component checklist prior to installation. If any parts are missing or for

IMPORTANT: Ensure that you have received all pants according to the component checklist prior to installation. If any pants are missing or faulty, contact your place of purchase for a replacement.

MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at least every three months).

The following table provides the information obtained from the United States

Technical line drawing of a mechanical support bracket with internal striped component (no text or symbols)

TN-70F

200x100/200x200 300x200/300x300 400x200/400x300 400x400