Alphagraph Chrono - Wristwatch Daniel Steiger - Free user manual and instructions

Product Type	Wristwatch
Brand	Daniel Steiger
Model	Alphagraph Chrono
Category	Watch
Movement	Quartz
Display	Analog with chronograph subdials
Functions	Time (hours, minutes, seconds), Date, Chronograph (up to 11h59m59s, 1/1 second)
Crown Positions	Position 0: normal; Position 1: date setting; Position 2: time setting
Chronograph Buttons	Button A: start/stop; Button B: reset
Battery Type	Standard watch battery (e.g., SR626SW)
Water Resistance	Not specified (avoid contact with water)
Case Material	Stainless steel
Crystal	Mineral glass
Battery Life	Approximately 2-3 years
Maintenance	Clean with soft dry cloth; avoid moisture; replace battery when needed
Special Note	Avoid setting date between 9 PM and 1 AM
Chronograph Reset	If hands don't return to zero, pull crown to 2nd position, press Button A to adjust, then push crown back

Frequently Asked Questions - Alphagraph Chrono Daniel Steiger

How do I set the time on my Daniel Steiger Alphagraph Chrono?

Pull the crown out to the 2nd position. Turn the crown to set the hour and minute hands. Push the crown back to the normal position, and the small second hand will start running.

How do I set the date?

Pull the crown out to the 1st position. Turn the crown counter-clockwise to set the date. Avoid setting the date between approximately 9:00 PM and 1:00 AM to ensure proper date change. Push the crown back to normal position.

How do I use the chronograph?

Press button A to start or stop the chronograph. Press button B to reset the chronograph hands to zero. The chronograph can measure up to 11 hours 59 minutes 59 seconds in 1/1 second increments.

What should I do if the chronograph hands do not return to zero after reset?

Pull the crown out to the 2nd position. Press button A repeatedly to advance the chronograph second hand until it aligns with the zero position. For rapid advance, press and hold button A. Once zeroed, push the crown back to normal position. Do not push the crown while the hand is still moving.

How do I reset the chronograph after a battery replacement?

Follow the same procedure as for an incorrect zero position: pull crown to 2nd position, use button A to set the chronograph second hand to zero, then return crown to normal position.

Is the watch water resistant?

The manual does not specify water resistance. To avoid damage, it is recommended to keep the watch away from water and moisture.

Can I swim with this watch?

No, as water resistance is not specified, swimming or any water exposure may damage the watch.

How often should I replace the battery?

The battery typically lasts 2-3 years. Replace it when the watch stops or the chronograph behaves erratically. Have it replaced by a professional.

How do I clean the watch?

Use a soft, dry cloth to gently wipe the case and strap. Avoid using chemicals or water. For leather straps, keep them dry.

What should I avoid when setting the date?

Avoid setting the date between 9:00 PM and 1:00 AM as the date mechanism may be engaged and improper setting could damage the movement.

USER MANUAL Alphagraph Chrono Daniel Steiger

A) DISPLAYS AND BUTTONS

B) SETTING THE TIME

C) SETTING THE DATE

D) USING THE CHRONOGRAPH

E) CHRONOGRAPH RESET (INCL. AFTER REPLACING BATTERY)

B) SETTING THE TIME

1. Pull the crown out to the 2nd position.

2. Turn the crown to set hour and minute hands.

3. When the crown is pushed back to the normal position, small second hand begins to run.

C) SETTING THE DATE

1. Pull the crown out to the 1st position.

2. Turn the crown counter-clockwise to set the date.

*If the date is set between the hours of around 9:00 PM and 1:00 AM, the date may not change on the following day.

1. After the date has been set, push the crown back to the normal position.

D) USING THE CHRONOGRAPH

This chronograph is able to measure and display time in 1/1 second united up to maximum of 11 hours 59 Minutes 59 seconds.

The chronograph second hand keeps continuously for 11 hours 59 minutes 59 seconds after starting. Measuring time with the chronograph

1. The chronograph can be started and stopped each time button "A" is pressed.

2. Pressing button "B" resets the chronograph and the chronograph second hand, chronograph minute hand, and chronograph hour hand return to zero position.

"A"

RESET "A" TIME MEASUREMENT STOP

"B" "A"

"B"

E) CHRONOGRAPH RESET (INCL. AFTER REPLACING BATTERY)

This procedure should be performed when the chronograph second hand does not return to zero position after the chronograph has been reset, and including after the battery has been replaced.

1. Pull the crown out to the 2nd position.

2. Press button "A" to set the chronograph second hand to the zero position. The chronograph hand can be advanced rapidly by continuously pressing button "A".

3. Once the hand have been zeroed, return the crown to the normal position.

* Do not push crown to normal position while the chronograph second hand returns to zero position. It stops on the way when crown are returned to normal position and its position is recognized as zero position.