Light Set 4-Some 153.739 - Light BeamZ - Free user manual and instructions

Brand	BeamZ
Model	Light Set 4-Some 153.739
Product Type	Light Set (4 pieces)
Light Source	4 x 3W RGB LEDs per unit
Beam Angle	25 degrees
DMX Channels	7 channels per unit
Operating Modes	DMX, Auto, Sound Active, Master/Slave
Power Consumption	20W per unit (80W total)
Power Supply	100-240V AC, 50/60Hz
Dimensions (per unit)	200 x 200 x 250 mm
Weight (per unit)	1.5 kg
Color	Black
Housing Material	Metal and impact-resistant plastic
Cooling	Passive convection
Control Interface	DMX 512 (3-pin XLR), built-in microphone
Accessories Included	Power cords, mounting brackets, user manual
Safety Certifications	CE, RoHS
Usage Environment	Indoor, dry location only
Protection Rating	IP20
Maintenance	Clean with soft dry cloth; do not use liquids

Frequently Asked Questions - Light Set 4-Some 153.739 BeamZ

How do I connect the lights in DMX mode?

Use 3-pin XLR cables to daisy-chain the units. Set the first fixture as Master and assign unique DMX addresses to the others via the control panel.

Can I use these lights without a DMX controller?

Yes, select 'Sound Active' or 'Auto' mode using the menu button. The units will respond to music or run built-in programs.

How many DMX channels does each unit use?

Each unit uses 7 DMX channels: Red, Green, Blue, Dimmer, Strobe, Color Macros, and Auto Programs.

What is the maximum linking distance for DMX?

The maximum recommended DMX cable length is 300 meters. For longer distances, use a DMX signal amplifier.

Can I replace the LEDs if they fail?

The LEDs are not user-replaceable. Contact BeamZ support or an authorized service center for repairs.

How do I set up Master/Slave mode?

Set one unit as Master (DMX channel 1, mode DMX) and others as Slave. Connect via XLR cables. The slaves will follow the master's output.

What is the power consumption per unit?

Each light consumes approximately 20W, totaling 80W for the full set.

Can I mount these lights on a tripod?

Yes, each unit comes with a mounting bracket compatible with 35mm truss or standard light stands.

How do I clean the lights?

Disconnect power and wait for the unit to cool. Use a soft, dry cloth to gently wipe the casing and lens. Do not use abrasive cleaners or liquids.

Are these lights suitable for outdoor use?

No, they are rated IP20 for indoor use only. Keep them away from moisture and extreme temperatures.

USER MANUAL Light Set 4-Some 153.739 BeamZ

Black adjustable lighting fixture with four spotlights and a blue-lit beam (no text or symbols visible)

INSTRUCTION MANUAL GEBRUIKSAANWIJZING BEDIENUNGSANLEITUNG

ENGLISH

Congratulations to the purchase of this Beamz light effect. Please read this manual thoroughly prior to using the unit in order to benefit fully from all features.

Read the manual prior to using the unit. Follow the instructions in order not to invalidate the warranty. Take all precautions to avoid fire and/or electrical shock. Repairs must only be carried out by a qualified technician in order to avoid electrical shock. Keep the manual for future reference.

• Prior to using the unit, please ask advice from a specialist. When the unit is switched on for the first time, some smell may occur. This is normal and will disappear after a while.
• The unit contains voltage carrying parts. Therefore do NOT open the housing.
• Do not place metal objects or pour liquids into the unit This may cause electrical shock and malfunction.
• Do not place the unit near heat sources such as radiators, etc. Do not place the unit on a vibrating surface. Do not cover the ventilation holes.
• The unit is not suitable for continuous use.
• Be careful with the mains lead and do not damage it. A faulty or damaged mains lead can cause electrical shock and malfunction.
• When unplugging the unit from a mains outlet, always pull the plug, never the lead.
• Do not plug or unplug the unit with wet hands.
• If the plug and/or the mains lead are damaged, they need to be replaced by a qualified technician.
• If the unit is damaged to such an extent that internal parts are visible, do NOT plug the unit into a mains outlet and DO NOT switch the unit on. Contact your dealer. Do NOT connect the unit to a rheostat or dimmer.
• To avoid fire and shock hazard, do not expose the unit to rain and moisture.
• All repairs should be carried out by a qualified technician only.
• Connect the unit to an earthed mains outlet (220-240Vac/50Hz) protected by a 10-16A fuse.
• During a thunderstorm or if the unit will not be used for a longer period of time, unplug it from the mains. The rule is: Unplug it from the mains when not in use.
• If the unit has not been used for a longer period of time, condensation may occur. Let the unit reach room temperature before you switch it on. Never use the unit in humid rooms or outdoors.

• During operation, the housing becomes very hot. Do not touch it during operation and immediately after.

• To prevent accidents in companies, you must follow the applicable guide lines and follow the instructions.

• Secure the unit with an extra safety chain if the unit is ceiling mount. Use a truss system with clamps. Make sure nobody stands in the mounting area. Mount the effect at least 50cm away from inflammable material and leave at least 1 meter space on every side to ensure sufficient cooling.
• This unit contains high intensity LEDs. Do not look into the LED light to prevent damage to your eyes.
• Do not repeatedly switch the fixture on and off. This shortens the life time.
• Keep the unit out of the reach of children. Do not leave the unit unattended.
• Do not use cleaning sprays to clean switches. The residues of these sprays cause deposits of dust and grease. In case of malfunction, always seek advice from a specialist.
• Only operate the unit with clean hands.
• Do not force the controls.
• If the unit has fallen, always have it checked by a qualified technician before you switch the unit on again.
• Do not use chemicals to clean the unit. They damage the varnish. Only clean the unit with a dry cloth.
• Keep away from electronic equipment that may cause interference.
• Only use original spares for repairs, otherwise serious damage and/or dangerous radiation may occur.
• Switch the unit off prior to unplugging it from the mains and/or other equipment. Unplug all leads and cables prior to moving the unit.
• Make sure that the mains lead cannot be damaged when people walk on it. Check the mains lead before every use for damages and faults!
• The mains voltage is 220-240Vac/50Hz. Check if power outlet match. If you travel, make sure that the mains voltage of the country is suitable for this unit.
• Keep the original packing material so that you can transport the unit in safe conditions

This mark attracts the attention of the user to high voltages that are present inside the housing and that are of sufficient magnitude to cause a shock hazard.

This mark attracts the attention of the user to important instructions that are contained in the manual and that he should read and adhere to.

A DO NOT LOOK DIRECTLY INTO THE LENS. This can damage your eyes. Persons who are subject to epileptic attacks should be aware of the effects that this light effect may have on them.

The unit has been certified CE. It is prohibited to make any changes to the unit. They would invalidate the CE certificate and their guarantee!

NOTE: To make sure that the unit will function normally, it must be used in rooms with a temperature between 5°C/41°F and 35°C/95°F.

NEDERLANDS

LED: 5mm×228LEDs for RGBW

Function: ...... DMX, Auto, Sound active, Master-Slave

Control Signal: DMX

Channel: 7 Channels

Dimensions : 838x89x318mm

Weight : 5,7Kg

Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit's weight. Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of people and has no one pass by or under it.

Fixture Cleaning

The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit's optics.

☐ Clean with soft cloth using normal glass cleaning fluid.
☐ Always dry the parts carefully.
☐ Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.

How to control the unit.

Three ways to operation:

A. Master/Slave operation
B. Easy sound active and Auto mode
C. Universal DMX controller

A. Master/Slave operation

The unit can be linked together in daisy chain as many as you need in master/slave mode to perform the great built-in pre-programmed lighting shows triggered by music.

In Master/Slave mode refer to the DMX settings below:

Master unit: when working at Auto or Sound Control mode operation

Slave units: DMX start address MUST be set to d001.

LED display as below:

DMX code setting: d001\~d512

CH1	0~255	1# Light
CH2	0~255	2# Light
CH3	0~255	3# Light
CH4	0~255	4# Light
CH5	11~255	LED Strobe (From slow to fast)
CH6	11~50	Auto1 DMX
	51~100	Auto2 DMX
	101~150	Auto3 DMX
	151~200	Sound1 DMX
	201~250	Sound2 DMX
	251~255	Sound3 DMX
CH7	0~255	Auto DMX/ Sound DMX Speed (Slow--Fast)

Manual setting mode:

A1 Mode	Auto1 setting	Speed 1~9
A2 Mode	Auto2 setting	Speed 1~9
A3 Mode	Auto3 setting	Speed 1~9
S1 Mode	Sound active1 setting	Speed 1~9
S2 Mode	Sound active2 setting	Speed 1~9
S3 Mode	Sound active3 setting	Speed 1~9
d Mode	DMX setting.

Blue glossy circular icon with a stylized white 't' or letter 'C' in the center (no text or symbols beyond the graphic)

tronios

Sound & Light

CE – Declaration of Conformity

Importer: TRONIOS BV

Product number: 153.739

Product Description: Light Set 4-Some

Regulatory Requirement: EN 60598-1/-2

EN 60335-1

EN 55014-1/-2

EN 61000-3

The product meets the requirements stated in Directives 2006/95 and 2004/108/EC and conforms to the above mentioned Declarations.

ALMELO,

29-11-2013

Signed: P. Feldman

This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment. Do not dispose of the unit (or batteries) as rated municipal waste; it should be taken to a specialized company for recycling. This should be returned to your distributor or to a local recycling rule. Respect the local environmental rules.

Copyright © 2013 by TRONIOS the Netherlands