Q: What is the maximum cutting width of the DEXTER POWER TS8 table saw?

The maximum cutting width of the DEXTER POWER TS8 table saw is approximately 300 mm (30 cm) , measured to the right of the saw blade. This distance represents the maximum possible gap between the blade and the parallel guide (parallel stop). According to the technical specifications of the TS8, the saw has a blade diameter of 210 mm with a maximum cutting depth of 48 mm at 90°. The machine itself measures 485 mm in width, which also determines this maximum cutting width. To use this maximum cutting width: Loosen the stop buttons of the parallel stop Move the guide to the desired position using the graduated scale on the table Check the width with a test cut before cutting your final piece, as the scale may have slight inaccuracies Tighten the stop buttons firmly to secure the guide Note that the parallel guide can be mounted on both sides of the table, offering some flexibility depending on your work setup. For pieces wider than 300 mm, you will need to move the guide to the other side of the blade or use other guiding techniques. Always ensure that the parallel guide is properly aligned parallel to the saw blade (adjustment described in section 8.7 of the manual) to ensure accurate and safe cuts.

Question 1

Is there an installation video for the DEXTER POWER TS8 table circular saw?

Accepted Answer

For the DEXTER POWER TS8 model, there is no official installation video published by the manufacturer. However, you have a detailed installation manual in PDF format that comes with the product. This manual contains clear and illustrated instructions for:

Assembling and mounting the base as well as the cart
Installing the blade safely
Making essential adjustments for optimal operation
Setting up safety devices

If you prefer visual assistance, you can check out videos on similar models from the DEXTER brand, such as the TS100 or TS100S, available on platforms like YouTube. These videos generally follow a similar assembly principle and can guide you through the installation steps.

In summary, although there is no official video for the TS8, the PDF manual remains the most reliable source for its installation, possibly supplemented by videos of similar models.

Question 2

How to make a 45° flat cut with the DEXTER POWER TS8 table circular saw?

Accepted Answer

To make a 45° flat cut with your DEXTER POWER TS8 table circular saw, you will need to tilt the blade to the left. Start by unplugging the saw and check that there is no collision between the blade and the table or guides before you begin.

Angle adjustment: Locate the adjustment wheel (8) on the side of the table and the associated locking handle (9). Loosen the locking handle, then turn the wheel (8) to set the angle to 45° on the graduated scale. This saw allows tilting from 0° to 45° to the left. Once the desired angle is reached, securely tighten the locking handle (9) to prevent any shifting during the cut.

Positioning the workpiece: Place your workpiece flat on the table against the parallel guide (7). Ensure that the piece is stable and well supported against the guide. For a 45° cut, the back of the parallel guide must follow the rule of thumb: position the stop so that its back intersects an imaginary line starting from the center of the saw blade and extending back at 45°.

Executing the cut: Plug in the saw and turn it on. Gradually advance your workpiece towards the blade while maintaining steady pressure against the parallel guide. Allow the saw to operate without forcing it. Once the cut is complete, turn off the machine and wait for the blade to come to a complete stop before removing the piece.

Important points: Never use the saw freehand. For 45° cuts, always use the parallel guide (7) to guide the piece. Do not combine the angle guide with the parallel guide, as this increases the risk of jamming and kickback of the piece. With a 45° angle, the cutting depth will be reduced compared to a straight cut (the maximum goes from 48 mm at 90° to about 34 mm at 45°).

Safety: Always wear protective goggles and appropriate gloves. Work in a well-lit environment and avoid any distractions. Keep your hands away from the blade while cutting and use a push stick if necessary to maintain your grip away from the blade.

Question 3

What is the maximum cutting width of the DEXTER POWER TS8 table saw?

Accepted Answer

The maximum cutting width of the DEXTER POWER TS8 table saw is approximately 300 mm (30 cm), measured to the right of the saw blade. This distance represents the maximum possible gap between the blade and the parallel guide (parallel stop).

According to the technical specifications of the TS8, the saw has a blade diameter of 210 mm with a maximum cutting depth of 48 mm at 90°. The machine itself measures 485 mm in width, which also determines this maximum cutting width.

To use this maximum cutting width:

Loosen the stop buttons of the parallel stop
Move the guide to the desired position using the graduated scale on the table
Check the width with a test cut before cutting your final piece, as the scale may have slight inaccuracies
Tighten the stop buttons firmly to secure the guide

Note that the parallel guide can be mounted on both sides of the table, offering some flexibility depending on your work setup. For pieces wider than 300 mm, you will need to move the guide to the other side of the blade or use other guiding techniques.

Always ensure that the parallel guide is properly aligned parallel to the saw blade (adjustment described in section 8.7 of the manual) to ensure accurate and safe cuts.

User manual DEXTER POWER : user manuals and guides in PDF

Models DEXTER POWER most viewed

Browse manuals DEXTER POWER by appliance type

Recent questions about devices DEXTER POWER