602-249V2 - Radiowecker LA CROSSE TECHNOLOGY - Kostenlose Bedienungsanleitung

Produkttyp	Radiowecker
Modell	602-249V2
Marke	La Crosse Technology
Abmessungen	17,12 cm x 3,86 cm x 8,71 cm
Stromversorgung	5 V USB-Netzkabel (im Lieferumfang)
Batterie-Backup	CR2032 Lithium-Knopfzelle (separat erhältlich)
Display	Gebogene LED-Anzeige mit Innenraumtemperatur und Luftfeuchtigkeit
Wecker	2 programmierbare Wecker (AL1, AL2)
Schlummerfunktion	Programmierbar von 5 bis 60 Minuten (Standard 5 Minuten)
Hintergrundbeleuchtung	Einstellbar in drei Stufen: Hoch, Niedrig, Aus
Auto-Dim	Automatische Abdunkelung zu festgelegter Startzeit und Dauer (1–12 Stunden)
USB-Ladeanschluss	1 Amp maximaler Ausgangsstrom (nur zum Laden, nicht zur Stromversorgung des Weckers)
Temperaturbereich	0 °C bis 50 °C
Luftfeuchtigkeitsbereich	20 % bis 95 % relative Luftfeuchtigkeit
Weckerdauer	5 Minuten
Sommerzeit (DST)	Manuelle Einstellung per Tastendruck
Garantie	1 Jahr eingeschränkte Garantie ab Kaufdatum
Pflegehinweise	Batterien nicht mischen, Kontakte reinigen, Polarität beachten
Sicherheitswarnung	Knopfzelle: Verschluckungsgefahr – sofort ärztliche Hilfe suchen
Hilfe & Support	Telefon: [phone], Online: bit.ly/contact_techsupport

Häufig gestellte Fragen - 602-249V2 LA CROSSE TECHNOLOGY

Wie stelle ich den Wecker ein?

Halten Sie die Taste AL1-2 gedrückt, bis die Anzeige blinkt. Mit den Tasten + oder DST/- stellen Sie die Stunden und Minuten für Wecker 1 und 2 ein. Bestätigen Sie mit AL1-2 und verlassen Sie das Menü mit SET.

Wie aktiviere oder deaktiviere ich die Wecker?

Drücken Sie die Taste AL1-2 wiederholt: Einmal für Wecker 1, zweimal für Wecker 2, dreimal für beide, viermal zum Deaktivieren. Das entsprechende Wecker-Symbol zeigt den Status an.

Wie stelle ich die Schlummerfunktion ein?

Halten Sie die Taste SET gedrückt, bis das Einstellungsmenü erscheint. Blättern Sie mit + oder DST/- zum Punkt Snooze Duration und wählen Sie eine Dauer zwischen 5 und 60 Minuten. Bestätigen Sie mit SET.

Wie ändere ich die Helligkeit der Hintergrundbeleuchtung?

Drücken Sie die Taste AUTO DIM SET kurz, um zwischen den Stufen HI (hoch), LO (niedrig) und OFF (aus) zu wechseln.

Wie aktiviere ich die automatische Abdunkelung (Auto Dim)?

Halten Sie die Taste AUTO DIM SET gedrückt, bis OFF angezeigt wird. Drücken Sie + oder DST/-, um die Funktion zu aktivieren. Stellen Sie die Startzeit und die Dauer (1–12 Stunden) ein. Das Auto-Dim-Symbol erscheint, wenn die Funktion aktiv ist.

Wie lege ich die Sommerzeit (DST) um?

Halten Sie die Taste DST/- für einige Sekunden gedrückt, um die Uhr um eine Stunde vorzustellen (Sommerzeit) oder wieder zurück (Winterzeit). Bei aktiver Sommerzeit erscheint der Buchstabe D im Display.

Was mache ich, wenn der Wecker ertönt?

Drücken Sie die Taste AL1-2, um den Wecker für diesen Tag auszuschalten. Das Wecker-Symbol bleibt eingeschaltet. Für die Schlummerfunktion drücken Sie die Taste AUTO DIM SET. Der Wecker wiederholt sich nach der eingestellten Schlummerdauer.

Kann ich mein Handy über den USB-Anschluss laden?

Ja, der USB-Anschluss dient zum Laden externer Geräte mit bis zu 1 Amp. Schließen Sie das Ladekabel Ihres Geräts an. Der Anschluss versorgt den Wecker nicht mit Strom.

Warum wird die Temperatur oder Luftfeuchtigkeit nicht angezeigt?

Überprüfen Sie, ob das Gerät eingeschaltet ist und der USB-Stecker richtig sitzt. Die Sensoren befinden sich im Gehäuse. Bei Störungen setzen Sie den Wecker zurück, indem Sie die Batterie kurz entfernen und wieder einlegen.

Wie wechsle ich die Backup-Batterie (CR2032)?

Legen Sie den Wecker auf eine weiche Unterlage. Öffnen Sie das Batteriefach mit einem Schraubendreher, schieben Sie die Abdeckung nach unten und entnehmen Sie die alte Batterie. Legen Sie eine neue CR2032 mit dem Pluspol nach oben ein. Schließen Sie das Fach und ziehen Sie die Schraube fest.

BEDIENUNGSANLEITUNG 602-249V2 LA CROSSE TECHNOLOGY

CURVED LED ALARM CLOCK WITH INDOOR TEMPERATURE & HUMIDITY

Model: 602-249v2 DC: 040721

For more product information visit: bit.ly/laxtech_support

POWER UP

1. Insert the provided Stand into bottom of the Alarm Clock.
2. Insert the 5.0 Volt USB Power Cord into an outlet, then into your Alarm Clock.

SETTINGS

1. Hold the SET button to enter the Settings Menu.

2. Use the + or DST/- button to adjust values

3. Press the SET button to confirm and exit.

Settings Menu Order:

• Hours
• Minutes
  • 12/24 Hour
• Snooze Duration (05 minutes to 60 minutes)

Page | 2 Page | 3 Page | 4

TIME ALARMS

1. Hold the AL1-2 button to enter the Alarm Settings.
2. Use the + or DST/- button to adjust values.
3. Press the AL1-2 button to confirm and move to the next item.
4. Press the SET button anytime to exit the Alarm Settings.

Alarm Settings Order:

• Alarm 1 Hour
• Alarm 1 Minutes
  • Alarm 2 Hour
  • Alarm 2 Minutes

① Alarm 1 Icon will show when active
[Non-Text]
② Alarm 2 Icon will show when active

Activate | Deactivate Time Alarms:

- Press the AL1.2 button once to activate Alarm 1. The Alarm 1 Icon will show.

• Press the AL1.2 button a twice to activate Alarm 2. The Alarm 2 Icon will show.
• Press the AL1.2 button three times to activate both Alarms.
• Press the AL1.2 button four times to deactivate both alarms. Both the Alarm 1 and Alarm 2 icons will disappear.

Silence a Sounding Alarm:

• When an alarm sounds, the related Alarm Icon will flash.
• Press the AL1.2 button to stop the alarm for one day. The Alarm Icon will remain solid on the display.

Snooze:

- When an alarm sounds, press the AUTO DIM SET button to silence the alarm for the Snooze Duration selected in the Settings Menu.

Note: Default Snooze Duration is 5 minutes.

- The appropriate Alarm Icon will flash when snooze is active. Note: If the other Alarm sounds, it will override the Snooze function of the First Alarm. The First Alarm will sound again the next day.

ADJUSTABLE BACKLIGHT HI-LO-OFF

Press the AUTO DIM SET button to adjust the brightness of your clock (HI/LO/OFF).

AUTO DIM BACKLIGHT

1. Hold the AUTO DIM SET button until OFF and the Auto Dim
   Icon 📞 shows. Press the + or DST/- button to turn ON.
2. Press the AUTO DIM SET button to select the Auto Dim Start
   Time (10:00pm will flash). Press the + or DST/- button to adjust.
3. Press the AUTO DIM SET button to select the Auto Dim
   Duration from IHI to 12HI (8HI will flash). Press the + of DS1/- button to adjust
4. Press the AUTO DIM SET button to confirm and exit.

When the Auto Dim Icon 📄 is displayed, your backlight will automatically dim at the start time and brighten again at the stop time selected.

USB CHARGING PORT

Connect your external device's USB charging cable (sold separately) to the USB Charging Port.

Notes:

- Charging times will vary.

• USB Power Output: 1 Amp maximum current.

- Charge 1 Amp devices or devices that are self-regulating.

- This is a power output charging port. It does not provide power to the alarm clock.

DAYLIGHT SAVING TIME ADJUSTMENT

When observing Daylight Saving time: Hold the DST/- button for a few seconds to move your time ahead 1 hour. The letter "D" will show in front of the time when DST is active.

When observing Standard time: Hold the DST/- button for a few seconds to move your time back 1 hour.

INSTALL CR2032 BATTERY

Your clock requires one CR2032 lithium battery (sold separately) to provide backup power in the event of a temporary power interruption. 1. Place the alarm face down on a soft flat surface.

1. Use a screwdriver to open the battery compartment door. Slide the door down to remove it.

2. Insert one new CR2032 battery into the battery compartment with the PLUS (+) side facing up as indicated.

3. Slide the battery door back into place and tighten the screw.

Note: Backup battery will not run the clock display.

WARNING

WARNING:

1. This product may use a Button Cell Battery.

2. If swallowed, it could cause severe injury or death in just 2 hours.

3. Seek medical attention immediately.

WARNING - KEEP BATTERIES OUT OF REACH OF CHILDREN

1. Swallowing may lead to serious injury in as little as 2 hours or death, due to chemical burns and potential perforation of the oesophagus.

2. If you suspect your child has swallowed or inserted a button battery, immediately seek urgent medical assistance.

3. Examine devices and make sure the battery compartment is correctly

secured, e.g. that the screw or other mechanical fastener is tightened. 4. Do not use if compartment is not secure.

1. Dispose of used button batteries immediately and safely. Flat batteries can still be dangerous.

2. Tell others about the risk associated with button batteries and how to keep their children safe.

Page | 6 Page | 7 Page | 8Page | 5

WE'RE HERE TO HELP!

If you require additional support, get in touch with our friendly customer support team based out of La Crosse, WI.

Phone: [phone]

Online: bit.ly/contact_techsupport

Our knowledgeable customer support team is available: Monday-Friday, 8am-6pm CST.

JOIN THE CONVERSATION

Ask questions, watch detailed setup videos, and provide feedback on our social media outlets!

SPECIFICATIONS

Power Requirements: HX075B-0501200-CU 5 Volt USB Power Cord (included) CR2032 Battery (sold separately)

Battery Life: Over 12 Months

USB Output: 1A Maximum Current.

Temperature Range: 32°F TO 122°F Humidity Range: 20% to 95% RH

Humidity Range: 20% to 9 Alarm Duration: 5 Minutes

Snooze Duration: Programmable from 5-60 Minutes

Dimensions: 6.74" L x 1.52" W x 3.43" H

(17.12cm L x 3.86cm W x 8.71cm H)

WARRANTY INFO

La Crosse Technology, Ltd. provides a 1-year limited time warranty (from date of purchase) on this product relating to manufacturing defects in materials & workmanship.

La Crosse Technology, Ltd, 2830 S. 26th St., La Crosse, WI 54601 For Full Warranty Details Visit www.lassrocotechnology.com/

CARE + MAINTENANCE

- Do not mix old and new batteries. - Do not mix Alkaline, Lithium, standard, or rechargeable batteries.

- Always purchase the correct size and grade of battery most suitable for intended use

- Clean the battery contacts and also those of the de - Ensure the batteries have with correct polarity (+ / -)

- Remove batteries from equipment that will not be used for an extended period.

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna. - Increase the separation between the equip

- Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(1) This device may not cause harmful interference, and (2) This device must accept any interference received, in

operation.

CAUTION!

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

All rights reserved. This manual may not be reproduced in any form, even in part, or duplicated or processed using electronic, mechanical or chemical process without the written permission of the publisher.

3.2.10

This booklet may contain errors or misprints. The information it contains is regularly checked and corrections are included in subsequent editions. We disclaim any responsibility for any technical error or printing error, or their consequences. All trademarks and patents are recognized.

WARNING: This product can expose you to chemicals including styrene, which is known to the State of California to cause cancer. For more information go to: www.P65Warnings.ca.gov