KMC 1 - Haut-parleur KLIPSCH - Notice d'utilisation et mode d'emploi gratuit

MODE D'EMPLOI KMC 1 KLIPSCH

THANK YOU

Thank you for your purchase of the Klipsch® Music Center knob! The knob combines legendary Klipsch technology with Bluetooth® and apix® technology for truly hit fidelity music playback from your favorite music device. With a Bluetooth® connected phone you can also conveniently answer, converse and terminals, or ignore incoming calls, from the knob, its contemporary styling compliments any décor and you can take it almost anywhere with both AC and battery-power options.

AC POWER

To operate on AC power first select the one plug adapter (3 total supplied) that fills your AC bullet and insert into the supplied AC adapter. Plug other end of the AC adapter into back of the knit marked DC IN, then plug AC adaptor into a functioning wall socket. On AC power, if no streaming or connected audio is selected for one hour the knit will automatically go into READY mode.

BATTERY POWER

The knit has a built-in rechargeable lithium-ion battery capable of up to 6 hours of playing time. ALLOW 8 HOURS OF INITIAL CHARGE TIME BEFORE FIRST TIME BATTERY USE. Charging occurs when knit is plugged into active AC outlet. Pushing UTILITY button down with knit an other than during a Bluetooth connected phone call will show current battery strength. The knit operates on battery power unless AC power is utilized. On battery power, if no streaming or connected audio is detected for five minutes, the knit will automatically go into READY mode. To put the volt back into ON mode simply press the ON/2 READY button on log. Turn-off rear power switch to conserve battery.

USB CHARGING

NOTE: The USB jack is only for CHARGING most music players, phones, and labels. Using the USB connection end of the charging cable for your device (not included), connect to the USB input on rear of the kind to charge your device. You can charge your device using either AC or battery power for the kind. NOTE: Using the USB input to charge your device while the kind is on battery power will reduce battery life. If the battery in the kind is too weak, the USB connection will not charge your device.

ILLUMINATED CONTROL FUNCTIONS

graph TD
    A["8"] --> B["∞"]
    B --> C["-"]
    C --> D["+"]
    E["NFC"] --> F["7"]
    G["123546"] --> H[" "]
    I["∞"] --> J[" "]

1. ON / READY - Tap to turn on. Hold to put in READY mode.
   Solid Red indicates ON, flashes if batteries are weak
2. BLUETOOTH

3. VOLUME DOWN

1. VOLUME LEVEL / BATTERY LEVEL INDICATOR
2. VOLUME UP
3. UTILITY - Answer/Terminate or Ignore a phone call from a Bluetooth-connected phone OR check battery level
4. SOURCE SELECT - Pressing - and - together toggles between Bluetooth mode and AUX (3.5min input) for playback
5. MUTE - Briefly push ON/READY and VOLUME DOWN together to MUTE sound during music playback then briefly push same two buttons together again to unmute sound back to original level.

ANALOG MUSIC SOURCE

Any device with a standard 3.5mm headphone output can be connected to the AUX input (on back) with a min-to-mini cable (included). Make sure volume on knot is just above minimum, adjust volume on your device to max and play music. Use SOURCE SELECT to switch to AUX input if necessary. Adjust volume with the volume buttons on the knot to desired level.

BLUETOOTH MUSIC SOURCE

Any paired Bluetooth device within a 30 foot (9.1 m) range of the knic can wirelessly stream music. For a Bluetooth connected device, set the knic's volume to max and adjust the volume to the desired level using the Bluetooth streaming device.

PHONE CONVERSATIONS

You can answer/terminate or ignore a phone call from any paired Bluetooth phone. An incoming phone call will pause music and send your connected phone's ring band through the knob. To answer, briefly press the UTILITY button on the knob. Then listen and talk using the knob as you would a speakerphone. Adjust volume using the volume + and - buttons or the knob to desired level. Make the knkt's microphone during a phone call (so the caller cannot hear you by briefly pressing the ON/READY and VOLUME DOWN buttons together. Unmade the microphone by

briefly pressing the same: two buttons again. Terminate the call by briefly pressing the UTILITY button again. To ignore a call, press and hold the UTILITY button until the incoming call steps.

PAIRING BLUETOOTH DEVICES

Press and hold the Bluetooth button (+) until it flashes (- 3 seconds). Do not touch any other authors on the knot during this process. Activate the Bluetooth feature on your device, settling it up to pair with "Kilipsch knot". Once paired, the knot will automatically select Bluetooth as the source, we recommend following the volume settling instructions in the Bluetooth Music: Source section before playing any music, if the last pairs Bluetooth device is not available or not playing it will automatically choose the AUX (3.5mm input) as the source. The knot can stare up to 8 pairs Bluetooth devices.

CARE AND CLEANING

Your knic music center has a durable finish that only requires dry dusting or cleaning with a dry cloth. Avoid the use of abrasive or solvent-based cleaners and harsh detergents. Adhesive tape will clean up the rubber device area. Do not run hard, Window cleaner and a paper travel will clean the surface wall.

TROUBLESHOOTING

kind will not power on

- Make sure plug adapter is secured tightly to the AC adapter

- Make sure AC adapter is plugged tightly into DC input.

• Make sure AC adapter is plugged into a live outlet

• Make sure power switch is turned on

- If no AC connection make sure the battery is sufficiently

charged (POWER ON/OFF LED will dim/brighten every 5

seconds when the knot is running out of battery grower;

Device will not pair with bluetooth mode:

- Make sure knt is in pairing mode (x flashing blue)

• Make sure you are within 30 feet (9.1 m) of kmol while pair

ing; moves closer/make sure you are in the same room

• Make sure your volume settings are correct

Device does not play in Bluetooth/mose or AUX input

• Make sure volume on device is up to maximum/kncl vol

one is up at least half way and not MUTED

- If using AUX input, make sure connections are tight

- Touch + and - buttons together to select correct input

- If solid blue touch and hold + and - together to switch inputs For example, the input of a tool with two sets of 30% of the input are used by the input. The input is used for adding a small amount of 1000 units (e.g., 1000 units, 1000 units, 1000 units, 1000 units, 1000 units, 1000 units, 1000 units, 1000 units, 1000 units, 1000 units, 1000 units, 1000 units, 1000 units, 1000 units, 1000 units, 250 units, 250 units, 250 units, 250 units, 250 units, 250 units, 250 units, 250 units, 250 units, 250 units, 250 units, 250 units, 250 units, 250 units, 250 units, 250 units, 250 units,

Klipsch music center ENGLISH Klipsch® kmc1