Dress RS907CX9 - Kell Lorus - Tasuta kasutusjuhend

KASUTUSJUHEND Dress RS907CX9 Lorus

NREAD

12/2011

Instruction Manual

LORUS

ANALOGUE QUARTZ

LORUS

■HOW TO USE NON-CALENDAR MODEL

Normal position

First click

Put the crown OUT to the FIRST clock and set the time, then push the crown N.

Note: When you set the time, first set the minute hand to a properly covered time. Then return the rule hand to be correct time by turning it COUNTLOCKWISE.

■HOW TO USE DAY/DATE MODEL

The day of the week can be displayed by lingually (English/another language) and you can select other

1. How to set the day and date

Put out the crown to the first click position. (The crown of the watch can be outed out to the second click poston)

Turn the crown and set the previous day and date. (the day and date can be selected a thermotively and displayed in English or the other language.) (For Cal PC33, fum otherwise to set the care only.)

Put out the crown to the second o'clock position and set the present day and date by turning the minute hand.

Day selling for Cal. PC33

At the second click position, I am the non-clockwise and counter-clockwise repeatedly between 11:5 pm and 3/5 cm to select the desired day and language.

Note: Do not attempt to set the day and date between the times of 9:30 am and 4:00 am as this may cause the day and do e d solays to change out of sequence.

2. How to set the time

Put out the crown to the second click position and the second hard stool. The second hard should be slipped on 12 o'clock position.

Turn he grown and set the cooling ring.

Push the crown in other rooms cost on in occurrence with a the sign.

• Be sure to check that the AM/PM is correctly set (The day and date are designed to change once every 24 hours).
- To adjust the correct time for a square watch, it is necessary to advance the minute hand 4 c/5 minutes ahead of the correct time and then turn. It counts clockwise to set the designated line

LUMIBRITE WATCH

* I your watch is a LORUS LUM BRILL watch. It has to low ng features.

LORUS LUMBER TE watches closer and store light energy from natural and artificial light sources and on light in the dark. They are made of environmentally friendly materials, and therefore, are harmless to human beings and the environment.

• With a full charge, LORUS LU VIBRITE watches grow in the six hours longer than conventional luminous watches of this type. It exposed to a light of more than 600 lux (i.e., the brightness of a typical office) for approximately 10 minutes, or direct sunlight for 2 minutes, they will grow for hours
• Since LORUS LUMISKIF watches emit the light they store, the brightness will decrease gradually over time. The length of time they will glow may also differ slightly depending on such factors as the brightness of and distance from the light source used to charge the watch.
• With a full charge, LORUS LU VIBRITE watches grow in the six hours longer than conventional luminous watches of this type. It exposed to a light of more than 600 lux (i.e., the brightness of a typical office) for approximately 10 minutes, or direct sunlight for 2 minutes, they will grow for hours
• Since LORUS LUMISKIF watches emit the light they store, the brightness will decrease gradually over time. The length of time they will glow may also differ slightly depending on such factors as the brightness of and distance from the light source used to charge the watch.

BATTERY CHANGE

As the battery is inserted of the factory to check the function and performance of the watch. Is so dull. He once in your possession may be less than the special period.

Be sure to replace the battery to prevent any possible malfunction as soon as it runs down. To replace the battery, we recommend taking the watch to a local watch retainer.

■ CARE OF YOUR LORUS WATCH

BATTERY

CAUTION

Do not expose the old battery to fire or recharge it. Keep it at a place beyond the reach of children. If a child swallows it, consult a doctor immediately.

- WATER RESISTANT

Name or Standard Indicator or Date (see Table)	Not specified with a other a) applies of 12.1	5-mining will be ing a water	3-min dark
No Indication	NO	NO	NO
WATER RESISTANT	Yes	NO NO	NO
WATER RESISTANT* (100N/10 BAR) at above	YES	YES NO	NO
WATER RESISTANT* (100N/10 BAR) at above	YES	YES YES NO

* If your watch is 200 M/23 BAR, 100 M/10 BAR or 50 M/s BAR water resistant, it is so indicated on the clo /case book
- Be to press the buttons or turn the crown when the watch is wet.
• I the water is exposed to salt water, since it in fresh water can then wine thoroughly

Caution:

Logather shops are no water resistant except so indicated, even if the watch hecd is water resistant.

- ALLERGIC REACTION

Because the case and band touch the skin directly, it is important to clean their regularity. If not, shirt sleeves may be saline and those with delicate skin may develop a mask. Please wear the watch with some pay to avoid any possible charge a reaction. If you develop a rash on your wrist, stop wearing and consulting physician.

• MAGNETISM

Your watch will be adversely affected by strong magnetism. Keep flow away from close contact with natural causes.

- SHOCKS AND VIBRATIONS

Your watch may be worn for rental spots activities, but be careful nor to drop it or hit it on hard surfaces.

• TEMPERATURE

Your watch is preadjusted so that constant accuracy may be insured at hotel temperature.

SERVICE

When your LCRS watch requires reset or providing, please see the enclosed WARRAN Y/QUARANLE

■HOW TO ADJUST BAND LENGTH

Sliding clasp band

1. Try up the adjusting fao with a small screwdriver or something with a sharpened tip.

2. Slide the close to adjust it to a desired size.

3. The grooves on the lock side of the correct should fill into the convex portion on the close, then close the adjust flop.

- Wrong method

If you do this way, the adjusting flap may be destroyed.

Eruited a library