Tronas 53 - Vacuum Cleaner Sonnenkönig - Free user manual and instructions

USER MANUAL Tronas 53 Sonnenkönig

Line drawing of a vacuum cleaner with open lid and wheels (no text or symbols)

ARTIKEL NUMMER: 40000382

FIRMA

Sonnenkönig of Switzerland

Olensbachstrasse 9-15

CH-9631 Ulisbach

Tel. [phone]

Sonnenkönig of Switzerland

Exploded view diagram of a vacuum cleaner with numbered parts for identification

Illustration of a coiled hose with two cylindrical components (no text or symbols)

A.

C.

E.

B.

D.

F.

Technical line drawing of a mechanical device with gears and housing (no text or symbols)

Technical line drawing of a cylindrical component mounted on a base with a flanged side (no text or symbols)

atronenfilter

Line drawing of a vacuum cleaner with open lid and wheels (no text or symbols)

NASSAUFNAHME

Line drawing of a vacuum cleaner with open lid and wheels (no text or symbols)

Line drawing of a vacuum cleaner with open lid and wheels (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

GEBLÄSEBETRIEB

Illustration showing three different water sources: a can with a rotation arrow, a faucet with water level, and a sun with a pointer (no text or symbols)

LAGERUNG

IEC IEC 60335-2-2:2009

IEC 60335-1:2010+A1+A2

IEC 60335-2-2:2019

ROHS 2011/65/EU

EMC 2014/30/EU

LVD 2014/35/EU

Line drawing of a vacuum cleaner with open lid and wheels (no text or symbols)

ARTICLE NR: 40000382

MAISON

Sonnenkönig of Switzerland

Olensbachstrasse 9-15

CH-9631 Ulisbach

Tel.[phone]

Sonnenkönig of Switzerland

Exploded view diagram of a vacuum cleaner with numbered parts for identification

Illustration of a coiled hose with two cylindrical components (no text or symbols)

A.

C.

E.

B.

D.

F.

RÉSUMÉ DU DÉBALLAGE ET DE L'INSTALLATION

Technical line drawing of a mechanical assembly with gears and housing (no text or symbols)

Technical line drawing of a cylindrical device mounted on a base, with no visible text or symbols.

Sachet-filtre jetablefiltre catridge

bre catridge

Line drawing of a vacuum cleaner with handle and wheels (no text or symbols)

RAMASSAGE DES LIQUIDES

Line drawing of a vacuum cleaner with control panel and air vent (no text or symbols)

Line drawing of a vacuum cleaner with control panel and fan (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

OPÉRATION DE SOUFFLAGE

REPLACEMENT DU FILTRE

Simple line drawing of a sun shining over a cylindrical container (no text or symbols)

STOCKAGE

08 - GARANTIE / CONFORMITÉ / MISE AU REBUT

Garantie

IEC IEC 60335-2-2:2009

IEC 60335-1:2010+A1+A2

IEC 60335-2-2:2019

RoHS 2011/65/EU

EMC 2014/30/EU

LVD 2014/35/EU

INSTRUCTIONS D'ÉLIMINATION DES COMPOSANTS ÉLECTRIQUES DU PRODUIT

Line drawing of a vacuum cleaner with open lid and wheels (no text or symbols)

NUMERO DI ARTICOLO: 40000382

DITTA

Sonnenkönig of Switzerland

Olensbachstrasse 9-15

CH-9631 Ulisbach

Tel.[phone]

Sonnenkönig of Switzerland

Exploded view diagram of a vacuum cleaner with numbered parts for identification

Illustration of a coiled hose with two cylindrical components (no text or symbols)

A.

C.

E.

B.

D.

F.

RIEPILOGO DEL DISIMBALLAGGIO E DELL'INSTALLAZIONE

Technical line drawing of a mechanical device with gears and housing (no text or symbols)

Technical line drawing of a cylindrical heating element mounted on a base (no text or symbols)

Sacchetto filtrante monouso

Technical line drawing of a mechanical component with internal channels and mounting brackets (no text or symbols)

Line drawing of a vacuum cleaner with open lid and wheels (no text or symbols)

Line drawing of a vacuum cleaner with control panel and air vent (no text or symbols)

Line drawing of a vacuum cleaner with open lid and wheels (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

Illustration showing three different water cycle behaviors: can rotation, faucet with water tap, and sun bending (no text or symbols)

PULIZIA

IEC IEC 60335-2-2:2009

IEC 60335-1:2010+A1+A2

IEC 60335-2-2:2019

RoHS 2011/65/EU

EMC 2014/30/EU

LVD 2014/35/EU

INFORMATIVA SMALTIMENTO RELATIVA ALLA PARTE ELETTRICA DEL PRODOTTO

Line drawing of a vacuum cleaner with open lid and wheels (no text or symbols)

ARTICLE NR.: 40000382

COMPANY

Sonnenkönig of Switzerland

Olensbachstrasse 9-15

CH-9631 Ulisbach

Tel. [phone]

Sonnenkönig of Switzerland

Please read and understand these manual completely before attempting to assemble, operate or install the product.

This manual contains important information about the installation, operation and maintenance of this convector. General safety information is presented on these first pages and is also found throughout this manual. Retain this manual for future reference and to educate new users of this product. This manual should be read in conjunction with the labeling on the product. Safety precautions are essential when dealing with mechanical or electronic powered equipment. These precautions are required when using, storing and maintaining this item. Using this equipment with due respect and caution will reduce the possibility of personal injury or property damage. Inspect the unit for damage after removing the packaging. If damage is suspected, do not operate the device and contact a specialist. The recyclable packaging material must not be kept accessible to small children, but must be disposed of properly. This device may only be used for the purpose for which it was expressly designed. Any other use is to be considered improper and consequently dangerous. The supplier is not liable for any personal injury and/or damage to property resulting from improper or incorrect use. Repairs to electrical equipment may only be carried out by qualified personnel. Improperly performed repairs and modifications to the equipment may result in dangerous consequences for the user, whereupon warranty claims will be rejected.

The following basic precautions should always be followed when handling electrical equipment:

To reduce the risk of fire, electric shock, or injury:

• Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing. Connect to a properly grounded outlet only. See Grounding Instructions.
• Do not expose to rain. Store indoors.
  • Always disconnect the plug from the wall outlet before removing the tank cover.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors or dropped into water, contact service center for assistance.
• Do not pull or carry by cord, use cord as a handle, close a door on cord or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Do not put any object into openings. Do not use with any openings blocked; keep free of dust, lint, hair and anything that may reduce air flow.
• Keep hair, loose clothing, fingers and all parts of body away from openings and moving parts.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.
• Do not use without dust bag and/or filters in place.
• Turn off all controls before unplugging.
  • Take extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present.
• Do not use the cleaner as a sprayer of flammable liquids such as oil-based paint, lacquers, etc.
• Do not vacuum toxic, carcinogenic, combustible or other hazardous materials such as asbestos, arsenic, barium, beryllium, lead, pesticides or other health endangering materials.
• Do not pick up soot, cement, plaster or drywall dust without filter and dust bag in place. These are very fine particles that may affect the performance of the motor or be exhausted back into the air. Additional dust bags are available.
• Do not leave the cord lying on the floor once you have finished the cleaning job. It can become a tripping hazard.
• Use special care when emptying heavily loaded tanks.

• To avoid spontaneous combustion, empty tank after each use.

• The operation of a utility vacuum can result in foreign objects being blown into eyes, which can result in eye damage. Always wear safety goggles when operating vacuum.

• STAY ALERT. Watch what you are doing and use common sense. Do not use vacuum cleaner when you are tired, distracted or under the influence of drugs, alcohol or medication causing diminished control.
  NOTE: Use only as described in this manual. Use only manufacturer's recommended attachments.
• This appliance is provided with double insulation. Use only identical replacement parts. See instructions for servicing double insulated appliances.
• Unplug before connecting the hose, nozzle and the like.

WARNING

SERVICING OF DOUBLE-INSULATED WET/DRY VACUUM

In a double-insulated Wet/Dry Vacuum, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated appliance, nor should a means for grounding be added. Servicing a double-insulated Wet/Dry Vacuum requires extreme care and knowledge of the system and should be done only by qualified service personnel. Replacement parts for a double-insulated Wet/Dry Vacuum must be identical to the parts they replace. The double-insulated Wet/Dry Vacuum is marked with the words „DOUBLE-INSULATED“ and the symbol ☐(squarewithin a square) may also be marked on the appliance.

To reduce the risk of injury from electric shock, unplug power cord before servicing the electrical parts of the Wet/Dry Vacuum.

IMPORTANT If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.

IMPORTANT Remove the plug from the socket before performing maintenance. Before using the machine make sure that the frequency and voltage shown on the rating plate correspond with the mains voltage. Specifications and details are subject to change without prior notice. The accessories shown in the pictures may vary from model to model.

IMPORTANT SAFEGUARDS The symbol on the product or packaging indicates that the product must not be treated as domestic refuse. Instead, it should be handed in to a collection point for the recycling of electrical and electronic components. By ensuring the product is treated in the correct manner, you will help prevent any negative impact on the environment and health that might arise were the product to be discarded as ordinary refuse. For further information about recycling, you should contact your local authorities, refuse collection service or the sales outlet where you bought the goods.

WARNING This product is NOT to be used for filtering of pathogens, for example COVID-19. Follow all local, state and federal guidance on general cleaning practices.

DEFINITIONS: SAFETY ALERT SYMBOLS AND WORDS

This instruction manual uses the following safety alert symbols and words to alert people to hazardous situations and the risk of personal injury or property damage.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in deathous injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, result in deathous injury

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor derate injury.

NOTICE: Indicates a practice notrelated to personal injury which, if not avoided, may result in property damage.

TO REDUCE THE RISK OF INJURY, USERS MUST READ INSTRUCTION MANUAL. DO NOT RUN UNATTENDED. DO NOT PICK UP FLAMMABLE, COMBUSTIBLE OR HOT MATERIALS. DO NOT USE AROUND EXPLOSIVE DUST, LIQUIDS OR VAPORS. ELECTRICAL DEVICES PRODUCE ARCS OR SPARKS WHICH CAN CAUSE FIRE OR EXPLOSION. DO NOT USE AT FILLING STATIONS OR ANYWHERE GASOLINE IS STORED OR DISPENSED. DO NOT VACUUM TOXIC OR CARCINOGENIC MATERIALS OR OTHER HEALTH ENDANGERING MATERIALS SUCH AS ASBESTOS OR PESTICIDES. ALWAYS USE PROPER EYE AND RESPIRATORY PROTECTION. TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT EXPOSE TO RAIN. STORE INDOORS. WHEN SERVICING, USE ONLY IDENTICAL REPLACEMENT PARTS. DO NOT TO BE USED AS A STEP STOOL.

03 - TECHNICAL DETAILS

	TRONAS 53	MODEL: AT19199-14B
Power 1200 W
Voltage / Frequency 220-240 Volt~ , 50/60 Hz
Tank capacity 53 Liter
Dimensions 600 x 550 x 675 mm
Power cord 4.8	m lenght
Hose	1.8 m x 6.4 cm
Motor single stAGE
Safty	IPX4
Weight	12 kg

Exploded view diagram of a vacuum cleaner with numbered parts for identification

1 Handle

2 ON/OFF switch

3 Power Cord

4 Lid Latch

5 Vacuum Port

6 Dust tank

7 Drain cap

8 Caster dolly

9 Wheel

10 Blowing port

11 Top cover

12 Thermal Baffle

13 Gasket

14 Motor

15 Gasket, Motor

16 Motor base

17 Motor Bottom support

18 Float

19 Float holder

20 Anchor

21 Suction seat assembly

22 Outlet assembly

23 Undercarriage

24 Storage box

25 Handle assembly

A Hose 1.8 m x 6.4 cm

B 2x extension wand

C Floor nozzle

D Crevice nozzle

E Utility nozzle

F Cartridge filter

G Disposable dust bag

Illustration of a coiled hose with two cylindrical components (no text or symbols)

A.

C.

E.

B.

D.

F.

05 - OPEARATING INSTRUCTIONS

UNPACKING & SET-UP SUMMARY

1. Pull lid latches in an outward motion, remove power head and some accessories that may have been shipped in the tank.
2. Attach the casters according to the instruction in this manual.
3. Before replacing power head, refer to this manual to ensure you have the proper filters installed for your cleaning operation.
4. Replace power head, and apply pressure with thumb to each latch until it snaps tightly in place. Make sure all lid latches are clamped securely.
5. Insert the flexible hose end into inlet of tank.
6. Attach the extension wands to the accessory end of the hose. Apply slight pressure until fitting is tight.
7. Attach one of the cleaning accessories (depending on your cleaning requirements) on the extension wands. Twist slightly to tighten the connection.
8. Plug the cord into the wall outlet. The vacuum is ready for use.

CASTER ASSEMBLY

• Invert dust tank, take the dolly to align the tank bottom sinking place. Secure with screws provided.
• Return dust tank assembly upright.

Technical line drawing of a mechanical assembly with gears and housing (no text or symbols)

WARNING: To reduce the risk of fire or explosion, do not operate this vacuum in areas with flammable gases, vapors or explosive dust in the air. Flammable gases or vapors include but are not limited to: lighter fluid, solvent-type cleaners, oil-based paints, gasoline, alcohol or aerosol sprays. Explosive dusts include but are not limited to: coal, magnesium, aluminum, and grain or gun powder. Do not vacuum explosive dust, flammable or combustible liquids or hot ashes. Do not use this vacuum as a sprayer for any flammable or combustible liquid. To reduce the risk of health hazards from vapors or dusts, do not vacuum toxic materials.

WARNING: The operation of any utility vacuum can result in foreign objects being blown into the eyes, which can result in severe eye damage. Always wear safety eyewear.

CAUTION: To reduce risk of hearing damage, wear ear protectors when using the vacuum for extended hours or when using it in a noisy area.

This vacuum is assembled at the factory and ready for use when you remove it from the carton. The unit is ready for dry vacuuming or blowing. After you plug the power cord into the wall receptacle, turn the unit "ON" by pushing the switch from position "O" to position "I". The "O" is the "OFF" position and the "I" is the "ON" position.

DRY PICK-UP

1. The filter must always be in correct position to reduce the risk of leaks and possible damage to vacuum. Make sure that the filter is completely covering the filter cage and that the clamp ring is as close to the lid as possible. Make sure there are no gaps between the filter and the lid. (See illustration). It is very important to assemble the filter to the cage without allowing any possible leaks or tears. Any leaks will allow the picked up debris to be blown out of the blowing port and back into the surrounding environment.

2. When using your vacuum to pick up very fine dust, it will be necessary to empty the dust tank and clean or replace the filter at more frequent intervals to maintain peak vacuum performance.

NOTE: A dry filter is necessary to pick up dry material. If you use the vacuum to pick up dust when the filter is wet, the filter will clog quickly and be very difficult to clean. If the filter gets wet, replace it before continuing to do dry pickups.

INSTALLING DISPOSABLE FILTER BAG

1. Slide the cardboard collar opening firmly onto the vacuum port deflector until it stops against the deflector wall.

2. Position the bag so that it is distributed around the inside of the tank.

3. Replace and secure the power head onto the tank.

Technical line drawing of a cylindrical heating element mounted on a base (no text or symbols)

Disposable filter bag Disposable filter bag

sposable filter

Line drawing of a vacuum cleaner with attached fan and wheels (no text or symbols)

WET PICK-UP

This wet/dry vac is equipped with a float mechanism which will rise automatically to cut off the airflow when the liquid in the tank reaches a predetermined level. When this happens, turn off vac, unplug the power cord, and empty the dust tank. You will know that the float has shut the airflow off because the suction ceases and the motor noise becomes higher in pitch due to increased motor speed. The liquid capacity may vary with the rate of pickup.

IMPORTANT: To reduce the risk of damage to the vac, do not run motor with float in raised position.

WARNING: To reduce the risk of injury from accidental starting, unplug power cord before emptying the dust tank.

EMPTY THE TANK

1. Remove the power head assembly of the wet/dry vac by pulling outward on the lid clips located on each side of the vac. Lift off the power head assembly.

2. Dump the tank contents into the proper waste disposal container.

Line drawing of a vacuum cleaner with control panel and air vent (no text or symbols)

Line drawing of a vacuum cleaner with open lid and air vent (no text or symbols)

Technical line drawing of a mechanical device with no visible text or symbols

BLOWING OPERATION

The vacuum contains a blowing feature. It has the capability to blow sawdust and other debris. It can be used to blow dust and debris out of garages or off patios and driveways. Follow the steps below to use the vacuum as a blower.

1. Locate blower port on the vacuum.
2. Insert one end of the hose into the blower port.
3. Turn vacuum "ON".

WARNING: Always wear safety eyewear when using as a blower. To avoid injury to bystanders, keep them clear of blowing debris.

CAUTION: Wear a dust mask if blowing creates dust which might be inhaled. To reduce the risk of hearing damage, wear ear protectors when using the vacuum/blower for extended hours or when using it in a noisy area.

06 - MAINTENANCE / CLEANING / STORAGE

FILTER REPLACEMENT

WARNING: To reduce the risk of injury from accidental starting, unplug power cord before changing or cleaning filter. Your filter should be cleaned often to maintain peak vacuum performance. Do not remove filter cage and float. The float prevents water from entering the impeller and damaging the motor. The cage prevents fingers from touching the moving impeller.

IMPORTANT: To avoid damage to the blower wheel and motor, always reinstall the reusable filter before using the vacuum for dry pickups and always reinstall the foam filter before using the vacuum for wet pickups. After cleaning, check the filter for tears or small holes. Do not use a filter with holes or tears in it. Even a small hole can cause a lot of dust to come out of your vacuum. Replace it immediately.

CLEANING

To keep the wet/dry vacuum looking its best, clean the outside with a cloth dampened with warm water and mild soap.

1. Dump out debris.
2. Wash tank thoroughly with warm water and mild soap.
3. Wipe out with dry cloth.

FILTER CLEANING

1. To remove the cartridge filter for cleaning, hold the power head and turn the filter retainer counter-clockwise to loose and remove.
2. To clean filter, brush off excess dirt with water, DRY completely (approximately 24 hours) and re-install.

Illustration showing three different water sources: a can with a rotation arrow, a faucet with water flowing into a well, and a sun with rays touching the surface (no text or symbols)

STORAGE

Before storing the ash vacuum, the dust tank should be emptied and cleaned. The accessories should be kept in the accessory holder so they can be readily available. The ash vacuum should be stored indoors.

Minor problems often can be fixed without calling customer service.

PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Vacum does not run No electricity	Make sure electrical outlet has	voltage (A qualified electrician may need to be contacted)
Loss of suction, wet or dry pick-up	1. Full tank2. Clogged hose3. Clogged filter	4. Drain and blean tank5. Remove hose and clean debris6. Clean or replace filter

08 - WARRANTY / CONFORMITY / DISPOSAL

Warranty

All products are checked from our company before the delivery. In case that there is a lack on your product, please contact the vendor. Please bring your proof of purchase for guarantees. Please save the packaging materials of the unit.

Disposal

Please remove the vacuum properly. You can bring the product to any specialist dealer fort he removal.

CE declaration of Conformity

This device complies with the following standards

EMC EN IEC 55014-1:2021

EN IEC 55014-2:2021

EN IEC 61000-3-2:2019+A1:2021

EN 61000-3-3:2013+A1:2019

LVD EN 60335-2-2:2010 + A11:2012 + A1:2013

EN 60335-1:2012 + A11:2014 + AC:2014 + A13:2017 + A1:2019 + A14:2019 + A2:2019

EN 62233:2008

IEC IEC 60335-2-2:2009

IEC 60335-1:2010+A1+A2

IEC 60335-2-2:2019

RoHS 2011/65/EU

EMC 2014/30/EU

LVD 2014/35/EU

DISPOSAL INSTRUCTIONS FOR THE ELECTRICAL PART OF THE PRODUCT

In accordance with Article 26 of the Decree-Law of 14 March 2014 implementing Directive 2012/19/EC, and the Law of 31 March 2015 implementing Directive 2015/863/EU on the reduction of the use of hazardous substances in electrical and electronic equipment and on waste management.

The crossed-out dustbin symbol on the machine or packaging indicates that the waste generated at the end of its useful life must be collected separately from other waste. The user must therefore take the device to the appropriate collection points at the end of its service life. Sort electronic and electrical waste or send back to the retailer when purchasing new, equivalent devices in a one-to-one process. Appropriate separate collection for subsequent commissioning of the equipment to be recycled, treatment and environmentally sound disposal helps to avoid possible adverse effects on the environment and health, and promote the reuse and/or recycling of the materials to which they belong. Misuse of this product by the user will result in the application of the administrative penalties provided for in the applicable legislation. Batteries contained in the device must be disposed of separately in the appropriate containers for the collection of used batteries.

Simple line drawing of a dart hitting the center with a crown (no text or symbols)