MUH360 - Humidifier N'oveen - Free user manual and instructions

USER MANUAL MUH360 N'oveen

Two white N'OVEEN water purifiers with control knobs, no visible text or symbols on the devices themselves.

INSTRUKCJA OBSŁUGI
USE INSTRUCTIONS

POLSKI s. 2

ENGLISH p. 7

Close-up of white plastic components with arrows indicating direction, no visible text or symbols

Close-up of white plastic components with arrows indicating direction, no visible text or symbols

Four-panel image showing a white plastic comb with ribbed structure before and after modification, labeled zdj. 3 to zdj. 6 (no text or symbols on the objects themselves)

The humidifier helps to eliminate the discomfort of dry air. Ultrasonic humidifier uses ultrasound to break down water molecules and generate mist. Read all safety instructions before use and keep this manual for later reference.

- Do not overfill the tank, unbalanced movement may cause excess water to run into the main body and damage the base unit.

- Do not touch the water in any part of the machine when the humidifier is working.

- Do not direct the sprayer nozzle towards children, furniture, walls, etc. Point it towards an empty space instead.

- Make sure the Ultrasonic Humidifier is positioned far away from other home appliances.

- Place the unit on an even, stable surface when in operation.

- When cleaning or moving the unit, turn it off, unplug it and remove the water tank.

• Take special care not to let water spill into the base.

- Do not place the humidifier in sun-lit places for long periods of time.

- Do not attempt to repair or replace parts yourself. Contact the Service Centre.

- Please unplug and store the Humidifier in its original packaging if it is not to be used for a long period of time.

- Never leave the appliance unattended while in use.

• Always unplug the appliance before filling it with water.

- Do not add any additives to the water (salt, oils, perfumes, etc.), which have not been provided by the distributor.

- Do not put the Humidifier on tables or on parquet or wooden flooring.

NOTE -The maximum operating time of the Humidifier is 12 hours.

1. Specifications

Water tank: 3.5 L

Power: 24 W

Maximum rating: 360 ml / hr

2. Components description

Nozzle Nozzle connection seat Handle Water tank Water tank bottom Thimble silicone Tank cover sealing ring Tank cover Thimble Float gland Float Fan Sensor Mist adjustment Fan cover Power Supply Board Dry reed pipe Dry reed pipe slice Aromization plate Anion Filter cotton tray Main body

3. General Introduction

The Ultrasonic Humidifier is made of recyclable plastic. It operates quietly, producing a cold, fine mist, the output of which can be regulated.

4. How Does it Work?

As per the vibrating theory of ultrasonic waves, the Ultrasonic humidifier uses the ultrasonic, high-frequency oscillator to break up water into tiny water particles with a diameter of about 1-5pm. The ventilation system then blows this water out into the dry air, where it evaporates to provide the required humidity. A mist will thus be released through the nozzle.

5. Directions

• Keep the unit under room temperature conditions for at least half an hour, before running the first operation.
• It is recommended to use the unit under temperature conditions of between 5 - 40 °C, and a relative humidity of less than 80 %RH.
• Remove the water tank from the main body, remove the tank cover found at the base of the water tank and fill the tank with tap water (not more than 40^ ), and securely tighten the tank cover to the water tank.
• Make sure that there are no debris in the main body that can damage the transducer..
• Connect the power plug and switch on the unit (NEVER SWITCH THE UNIT ON WHEN THERE IS NO WATER IN THE MAIN BODY), the main control lamp will then turn on.
• The unit is now ready for use.
• Turn the regulation knob to the desired setting
  In the case of lack of water, the device will stop working but the power light will remain on!

6. Filling the tank with water

Remove the water tank from the main body, unscrew the tank cap located in the tank base (zdj.1) and fill the tank with tap water (at a temperature no higher than 40^ C) and securely screw the cap (zdj.2)

Close-up of white plastic cups with arrows pointing to them, no visible text or symbols

Close-up of white plastic components with arrows indicating direction, no visible text or symbols

7. Dispensing oils

To use the aromatic oils you must do the following.

The dispenser is located on the back of the device (zdj. 3), pull it out (zdj. 4), then on the sponge in the middle (zdj. 5), put the right amount of oil (as desired). Then, close the dispenser to the position as in a photo (zdj.6). The device is ready for use.

Four-panel image showing a white plastic comb with serrated edges, labeled zdj. 3 to zdj. 6, showing a step-by-step assembly of the comb and final product.

8. Cleaning and Maintenance

8.1 Water Tank

Before cleaning, ensure that the unit is switched off. Clean after every use and do not keep water in the tank for longer than 2 days.

8.2 Transducer

To clean the (main body) transducer, add some de-scaling cleanser (about 0.5 g powder) onto the transducer and then add a small amount of water and wait for 2-5 minutes. Use a soft brush to clean. Do not use soap or other alkaline substances to clean the transducer.

9. Storage

We recommend that you store your Ultrasonic Humidifier in the original packaging. Make sure that all the parts are clean and dry before storage.

Troubleshooting

Problem	Possible reasons	Solution
Power light off	No power supply	Connect to power supply, switch on
Power light on, with breeze and no mist	No water in the water tank	Fill water into the water tank. Note: transducer may have already been damaged
Abnormal smell from the mist	New units may emit a strange odor	Remove the water tank, open the tank cover and let it stay out in the open for 12 hours in a cool, dry area
	Dirty water in the tank or water in the tank has been kept for too long	Clean the water tank and fill with clean water
Power light on, with low intensity	Too much water in the main body	Pour some water out from the main body, close the tank cover securely
Low intensity mist	Too much scale in the main body	Clean the transducer
	Dirty water in the tank or water in the tank has been kept for too long	Clean the water tank and fill with clean water
Abnormal noise	Resonance caused by too little water in the water tank	Fill with clean water
	Resonance caused by an unstable surface	Move the unit to a stable flat surface
Mist coming out beyond the nozzle	There are apertures between the nozzle and the water tank	Dip the nozzle in water for a while and then attach it to the socket on the water tank

Remember that before performing any activity consisting of opening, lifting or replacing, including dispensing oils, disconnect the device from the power supply !!!

KARTA GWARANCYJNA

IMPORTER / GWARANT :